quick_tips
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision | Next revision Both sides next revision | ||
|
quick_tips [2017/09/30 23:51] 192.168.1.194 |
quick_tips [2017/10/08 13:03] 192.168.1.194 |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Quick Tips ====== | ====== Quick Tips ====== | ||
| - | ===== Keeping Leggings extra stretchy ===== | + | ===== Keeping Leggings extra stretchy with Babylock ===== |
| Leggings need to be really comfy and very stretchy both at the hem and waistline. They are cut to fit and as they are being pulled over the waist, those coverstitches may need to stretch 25% or more. Here is an example of settings for cotton lycra with regular polyester overlocking thread on cones. I sew the hem with the leg turned inside out and stretching gently while sewing, to work as much thread as possible into every cm/inch. | Leggings need to be really comfy and very stretchy both at the hem and waistline. They are cut to fit and as they are being pulled over the waist, those coverstitches may need to stretch 25% or more. Here is an example of settings for cotton lycra with regular polyester overlocking thread on cones. I sew the hem with the leg turned inside out and stretching gently while sewing, to work as much thread as possible into every cm/inch. | ||
| Line 30: | Line 30: | ||
| - | ===== Snipping and turning the seam ===== | + | ===== And achieving the same stretch with Janome ===== |
| - | I tend to snip knit fabric to mark pattern details. Recently I started snipping the hem and waist folding line while my pattern is still on the fabric. This means that I am assembling and overlocking the snip so that no threads need to be severed. Not that I ever lost a seam!! It goes like this: | + | I always feel reluctant to offer "setting recipes" because every combination of machine, fabric and thread may require some testing and adjusting. When I tried the settings for the Babylock in the example above on a Janome Coverpro, I promptly got some skipped stitches when going over a side seam. |
| + | |||
| + | The Janome instruction manual recommends switching the looper to "tight" to avoid skipped stitches. I have not been able to get consistent good results with that adjustment. | ||
| + | My observation is that when I adjust the settings to get the stitches closer together to increase the stretch for leggings or other tight fitting garments, the risk of stitches skipping when going over a side seam or hump is related as much or even more to the tension on the needle thread, the left needle thread in particular. I explained this here | ||
| + | |||
| + | ===== Accessory number one for the Janome Coverstitch ===== | ||
| + | |||
| + | People often ask if any of the accessories are "must haves". It may be fun to experiment with accessories but I seldom consider them as necessary. There is one foot however that I think every Janome Coverpro owner should consider, and that is the shorter foot. Please compare the feet in the pics below. You will notice that the first one is shorter (+/- 5mm) than the second one. The first one is the new shorter foot and the one below is the standard foot that comes with the machine. | ||
| + | The standard foot is too long in my opinion and tends to increase the risk of fabric bunching up because it extends beyond the feed dogs. Maybe Janome should offer it as the standard foot?? | ||
| + | |||
| + | {{:quicktips:shorter_foot.jpg?800x600|}} | ||
| + | |||
| + | {{:quicktips:standard_foot.jpg?800x600|}} | ||
| - | {{:quicktips:overlocking_snipped_hemline.jpg?800x600}} | ||
| - | I just serge over the snips and then fold the side seam towards the back of the garment and the seam of the hem in the opposite direction. | ||
| - | {{:quicktips:turning_snipped_seam.jpg?800x600}} | ||
quick_tips.txt · Last modified: 2017/10/10 22:54 by 192.168.1.194
